How Deep Do Snap Weights Go?

A. You can easily get down to the 20-30

foot range

with

snap weights

. Depending on what speed you’re going, you should be able to reach those depths with a 3

ounce weight

and 40 to 60 feet of line after you put the weight on. I would recommend the weight to be 20 to 50 feet ahead of the lure.

Can you use snap weights with

planer boards

?

Of course, with your trolling spread you can mix up some snap weights with leadcore, wire, Dipsy Divers or flatlines. Most in-line planer boards will handle up to 3 ounces of lead, depending on the amount of line, speed and height of the waves.

What weights to use for trolling?

Use 3oz weight for 30′ and shallower trolling, 4oz for trolling to 40′ depths.

How does the 50 2 snap weight work?

The 50 Plus 2 Method starts by selecting one of the 16 crankbaits currently available with Snap Weight data and letting that lure back the designated 50 foot as a fixed leader. Next the two ounce OST Guppy Weight is attached to the line.

Should I use weight when trolling?

If you want to get the most out of this technique, remember that snap weight trolling is highly speed dependant The slower you go, the deeper the lure will run. This also applies to the amount of weight you use, heavier weights are also going to take your lure deeper.

How far behind the boat should I troll?


bait position

and Distance Behind Boat Proper distance for most boats will be anywhere from 20 feet to 150 feet behind your boat. Whether you have inboard diesel or outboard gas engines, your power dictates the distance you troll your baits and lures.

Do you use weights with crankbaits?

The answer is no. There is no need to use a weight or anything else with a crankbait Just tie it on to the end of your line and you’re good to go!.

How do I make my lures deeper when trolling?

If you need to go deeper, just let out some backing until your target depth is reached On the lure end of the line, remove a short section of lead as before and tie on a size 18, or smaller, barrel swivel. Now use a 10 to 15 foot mono or fluorocarbon leader to tie on the lure.

How much line should you let out when trolling?

Let out 50 feet of line and clip into the release. If that’s not enough distance to prevent your lake’s wary walleyes from seeing the ball.then let out 150 feet of line! Just remember, the flat-line diving depth of your crankbait still applies behind the ball!.

How do you calculate troll depth?

Consider the following example: If you’re trolling a tandem rig tied with two five-ounce bucktails (5 x 2 = 10), and you let out 100 feet of line (double 50, so multiply by two again), according to the Rule it will run at about 20 feet below the surface (5 x 2 = 10 x 2 = 20).

What is a trolling sinker?

A great sinker that takes bait rigs down to the deep feeding zones of big fish Attach your line to one end and a leader to the other, and your bait will stay right in the zone. Available in a variety of shapes from cigar to keel with bead chain and swivel or without and sizes ranging from 1/2 ounce to 5 ounce.

How deep should a trolling motor be in the water?

A trolling motor’s ideal propeller should be at a depth that keeps about 6 inches of water above the blades In other words, the centerline of the motor and the prop shaft should be about 12-18 inches below the waterline, depending on the make, model and dimensions of the trolling motor.

What size trolling motor do I need for a 16 foot boat?

If your boat is 16-foot or smaller, a high-thrust 12-volt model will be adequate for the conditions that you will face. If your boat is any longer, moving up to a 24- or 36-volt system is the only way to go for hassle-free boating.

Does trolling speed affect lure depth?

Trolling slightly faster or slower , the wind pushing the boat sideways, waves rocking the boat (tugging back and forth on the lures), underwater currents, water temperature, line diameter, variations in the lures (even though they look identical) and other factors all combine in very complex ways to affect a lure’s.

What are planer boards for fishing?

What Are Planer Boards? Planer boards are an effective way to fish additional lines when trolling Planer boards push your line to the side of your boat. This allows you to cover a wider area and also helps spread out multiple lines to prevent tangles.

How do you know how deep you are fishing?

Attach a float to your line and a weight where you would normally put the hook. Let it sink and the bobber will give you an idea of how deep the water is If it’s too deep, it will pull the bobber under and you will need to put more line between the float and the weight.

Citations


Snap Weight – 2 oz

Best Snap Weights for Trolling