Plug one end of the charger into the outlet and the other into the
receiver collar
The
collar light
is red while charging and green when fully charged. The first charge will take about 2 or 3 hours. Each charge can last up to 3 months depending on the frequency of use.
Can you replace battery in rechargeable PetSafe collar?
The PetSafe RFA-67 6V Replacement Battery 2-Pack are replacement batteries that work with the PetSafe bark collar, in-ground and
wireless fence receiver collar systems
These batteries are waterproof and last 1-3 months, depending on use.
How do I check the battery on my PetSafe collar?
All you have to do is hold the tool against the contact points on your dog or cat’s receiver collar to check if the collar is working properly. The test light tool will light up if static correction is being activated.
How long does PetSafe battery last?
Keep all of your pet’s essential electronics working their best with PetSafe RFA-67 6 Volt Replacement Batteries. The 2-count pack of 6 volt batteries can provide up to 6 months of power (each battery can last 1-3 months with proper use ). The patented design makes them easy to install and use.
When should I replace my PetSafe collar battery?
A replacement PetSafe® battery (RFA-67) can be found at many retailers. Contact the Customer Care Center at 1-800-732-2677 or visit our web site at www.petsafe.net to locate a retailer near you. Average battery life is 3 to 6 months , depending on how often your dog barks.
Why is my PetSafe bark collar not working?
If still no light, replace the battery with a new RFA-67 battery If the collar activates during testing but your dog is not responding to the correction, make sure the collar is properly fit. If the collar activates during testing and is properly fit but your dog is not responding, contact our Customer Care Team.
Why is the red light flashing on my petsafe collar?
Why is my Invisible Fence collar blinking red? If you have started to see a red flashing light on your pet’s
computer collar unit
, your Power Cap battery may need to be replaced You can order replacement batteries online, from your local dealer, or by calling 1-800-824-3647.
How long do petsafe collars last?
How long is the unit supposed to last? The Wireless Containment System unit can last up to approximately 10 years or more if used properly. Batteries on the collar can last and be replaced up to 1 to 2 months.
How long does it take a shock collar to charge?
It should take from 12-14 hours to fully charge batteries of both the transmitter and the collar. Remove the charger from the wall outlet when not in use.
How long do bark collars take to charge?
Before the first use, fully charge the bark collar for five hours. Every charge after will take 2-3 hours The average time between charges is 40 hours, depending on use. Lift the rubber cover protecting the charging port on the collar.
How long does it take to charge a dog collar?
Batteries require a full 2 hour charge before the first use. After initial charge, units will only take 2 hours to recharge. It is not harmful to let the unit charge for more than 2 hours. When storing the unit for long periods, give batteries a full 2 hour charge every 3 to 4 months.
Should the PetSafe collar blink?
PetSafe® Professional Batteries for the P4 Receiver The number of flashes indicates the shock level of the collar. However, it is not normal for the collar to continuously blink or flash after 5 or 10 flashes If it continues to flash, test the voltage of the batteries you are using.
How do you test the petsafe rechargeable bark control collar?
- Press and release the power button to power the collar on.
- Watch for the green light to blink twice, then hold the power button. Continue to hold the power button through the red light.
- Release the button when the light turns blue to set the collar into test mode.
How do you turn on a petsafe bark collar?
Use a large coin to turn the battery clockwise until the arrow lines up with the lock symbol on the housing This turns the Bark Control Collar on. To remove the battery, turn the battery counter- clockwise using a large coin. Removing the battery turns the Bark Control Collar off.
How do you turn on the petsafe spray bark collar?
- Remove the clear cap from the spray cartridge.
- Slide the door lock to the right to open the cartridge door.
- Insert the spray cartridge into the collar.
- Close the cartridge door until it clicks shut.
- Connect the charger to the collar.
- Hold the power button on the collar.
How do I reset my petsafe collar?
Reset your collar Press and hold the power button for 10 seconds to reset the collar The collar turns off, then flashes green and beeps to indicate that it has been reset. Release the button. Press and hold the button on the collar until a beep is heard and the light flashes green indicating that the collar has power.
What do you do when your bark collar doesn’t work?
The bark collar has not been fitted properly (very common) If the battery is flat, you simply need to recharge or replace the battery However, if the battery appeared to flatten too quickly we may need to look at things more closely. Often times a flat battery can relate to the most common problem.
Why does my petsafe collar beep but not shock?
If you do not feel a shock, then there may be a problem with the receiver collar Make sure you touch both points on the receiver at the same time when you hear the collar beeping. It will tell you definitively that the fence is or is not working.
Why does my petsafe transmitter keep beeping?
Continuous beep – Signal failure alarm There is an internal problem with the base unit. Alarm lasts up to 30 minutes.
Why does my petsafe collar keeps beeping?
If your house is very big and if the containment area has a relatively small radius, it’s likely that a part of the containment boundary falls somewhere inside your house , causing the collar to beep whenever it crosses that part of the boundary.
References
https://store.petsafe.net/test-light-tool
https://www.petsafe.net/media/downloads/400-003-1.pdf