In this blog post, I’m going to talk about the below topic, “Can You Reset Litter-Robot Remotely?.” I’ll share all the relevant information with you about the post. I hope this article will be very useful to you.
Remote Control The remote also allows you to reset the gauge when you empty the unit , helping the app learn your emptying behaviors to better tailor our gauge to match your needs.
How do you reset a Litter-Robot full sensor?
Press reset 2x to abort the cycle and return the unit to home (it will level the litter). 3. If the unit goes to
solid blue
with the
waste drawer
removed, ensure there is nothing in the drawer blocking the lenses.
How do you reset the blinking
yellow light
on a Litter-Robot?
Flashing yellow quickly Flashing quickly (about four times per second) means the
anti-pinch safety feature
detected a pinch condition. In this case, you will need to turn the Litter-Robot off and check the
waste port
in the base to remove any obstruction. Then turn the unit back on and hit the Reset button.
How do you fix the Litter-Robot?
Litter-Robot:
In terms of issues that may occur with your Litter-Robot 3, you may also see the blue light blinking. Before troubleshooting, it’s advisable to: Unplug your
power supply
and then wait for 10 seconds. Plug the unit back in and allow it to complete its cleaning cycle.
How do you force a Litter-Robot to cycle?
Litter-Robot:
Press the Cycle button The unit should cycle and return to Home with a solid blue light. Adjust your
cat sensor
by pressing the Reset button. Test CATS by pressing on the globe just above the entrance in a forward and downward motion.
How do I reset my Litter-Robot 2?
Litter-Robot:
Activate the cat sensor by pressing on the globe just above the entrance in a forward and down motion The red light should come on now. Allow the unit to complete the timing, cycle, and return to home position. At this time, the unit will have reset itself.
Why does my Litter-Robot keep saying drawer is full when I’ve just emptied and reset it?
Litter-Robot:
Debris may cause the DFI to indicate a full drawer regardless of the waste in the drawer Once you are done cleaning your unit, let it dry fully and then reassemble it.
Cat Sensor Fault: What is cat sensor fault on Litter-Robot
Sometimes after adding litter or replacing litter in the globe, the total weight of the globe becomes high enough that during the rotation or even while stationary (without cat inside) the cat sensor is triggered. If the Cat Sensor is triggered continuously for more than 2 minutes then the red light starts to blink.
Why is my Litter-Robot not cycling on its own?
Litter-Robot:
Reset the CATS by turning the unit off then on using the power button During the start-up cycle, push on the unit to see if the CATS activates. If it does, press “reset” to pause the cycle, then press “reset” again to return the unit to home position.
Cycle Button: Why is the cycle button blinking on my Litter-Robot
The
yellow light
flashing quickly is due to the anti-pinch feature The Anti-Pinch safety feature is two pin connected to the motherboard that must touch each other continuously.
Why does my Litter-Robot keep blinking blue?
Litter-Robot:
If the blue light on your Litter-Robot is flashing, it means your drawer is full and needs to be changed.
Litter-Robot Stuck: Why is my Litter-Robot stuck
Check for stuck litter, especially if you recently cleaned your unit ( leftover moisture may have interacted with the litter ). If you see debris or suspect there is litter caked behind the screen, you will need to clean the Globe (the screen should not be bent outward to clean behind).
Can two phones connect to Litter-Robot?
Litter-Robot:
Yes! You can onboard multiple WiFi-enabled Litter-Robot units or Feeder-Robot units to the Whisker app If others in your household want to use the app, they can simply download the app to their device and log in with the same account.
Will Litter-Robot still cycle if drawer is full?
Drawer:
A flashing blue light on the Litter-Robot III Open Air is the Drawer Full Indicator (DFI) sensor advising the waste drawer is full and needs to be emptied.
Citations
https://www.robotshop.com/community/forum/t/litter-robot-iii-open-air-hard-reset/29316
https://www.litter-robot.com/blog/litter-robot-troubleshooting-lights/